Planer - Revision history

Edejong22: /* General maintenance */

2025-08-12T18:55:07Z

General maintenance

2025-08-12T18:51:04Z

Description

2025-08-12T18:39:44Z

Description

2025-08-12T17:10:13Z

Specific Maintenance Tasks

2025-07-15T23:08:47Z

Certification

2024-08-22T22:04:05Z

Certification

2023-08-26T07:28:33Z

Certification

2023-01-23T19:47:04Z

2022-06-30T16:43:27Z

General Procedure

2022-06-30T16:15:59Z

General Procedure

@@ Line 113: / Line 113: @@
 ====General maintenance====
-General and specific tasks need to take place to maintain machinery. Specific tasks are listed below '''''Note: In [Specific Maintenance Tasks below, 5th item has redundant terms "use if rusted", not sure how to edit table - CZ]'''''
+General and specific tasks need to take place to maintain machinery. Specific tasks are listed below:
 ====Specific Maintenance Tasks====

@@ Line 50: / Line 50: @@
 The Planer is used to trim wood boards down by precise measurements, never more than 1/16 of an inch on each pass. The anti-kickback fingers and pressure bar are located in close proximity to the cutterhead for an exceptional finish. The solid cast iron base, table and head are designed for production. The 2-speed oil bath gearbox transmits full power to feed rollers and facilitates fast speed changes at 24 and 31 FPM. The gearbox can be changed to 4-speed with the included gear to run lower speeds of 16 and 20 FPM. The corrugated infeed and fine groove outfeed rollers ensure a smooth feed. The precision ground and polished cast iron table rides on four steel columns giving it plenty of support for the larger workpiece. Heavy cast iron extension wings ensure a flat, smooth cut.
 {{#evu:https://www.youtube.com/watch?v=NcGqyujNYlM}}
-{{#evu:}}
+{{#evu:https://www.youtube.com/watch?v=Aecl4v71Z4g}}
 ==Documentation==

@@ Line 50: / Line 50: @@
 The Planer is used to trim wood boards down by precise measurements, never more than 1/16 of an inch on each pass. The anti-kickback fingers and pressure bar are located in close proximity to the cutterhead for an exceptional finish. The solid cast iron base, table and head are designed for production. The 2-speed oil bath gearbox transmits full power to feed rollers and facilitates fast speed changes at 24 and 31 FPM. The gearbox can be changed to 4-speed with the included gear to run lower speeds of 16 and 20 FPM. The corrugated infeed and fine groove outfeed rollers ensure a smooth feed. The precision ground and polished cast iron table rides on four steel columns giving it plenty of support for the larger workpiece. Heavy cast iron extension wings ensure a flat, smooth cut.
 {{#evu:https://www.youtube.com/watch?v=NcGqyujNYlM}}
-{{#evu:https://www.youtube.com/watch?v=oRK0yW4CcWs}}
+{{#evu:}}
 ==Documentation==

@@ Line 137: / Line 137: @@
 |Ace
 |-
-|Clean Table surface. If rusted, use If rusted, use paste mixture of household ammonia, a good commercial detergent and 000 steel wool. Wash surface down with hot, soapy water, rinse and dry thoroughly. Coat surface with talcum powder, rubbing briskly into surface with a clean blackboard eraser.
+|Clean Table surface. If rusted, use paste mixture of household ammonia, a good commercial detergent and 000 steel wool. Wash surface down with hot, soapy water, rinse and dry thoroughly. Coat surface with talcum powder, rubbing briskly into surface with a clean blackboard eraser.
 |Before and after each use
 |Student and Ace

@@ Line 104: / Line 104: @@
 Complete the <strong>Wood Shop - {{PAGENAME}} Module</strong> at the link below to gain access to the {{PAGENAME}}. The Maker Hub Canvas course pertains to all facilities and equipment contained in the Maker Hub; simply complete the quizzes for the facilities/equipment you wish to use in the Maker Hub. Please email <span style="color:blue">makerhub@georgefox.edu</span> if you have any questions.
-[https://georgefox.instructure.com/enroll/GH36RT Maker Hub Canvas Course]
+[https://georgefox.instructure.com/enroll/R6RF69 Maker Hub Canvas Course]
 ==Troubleshooting==

@@ Line 102: / Line 102: @@
 ==Certification==
-[https://georgefox.instructure.com/courses/1245 Canvas Quiz]
+[https://georgefox.instructure.com/enroll/G7CTPX Maker Hub Canvas Course]
 ==Troubleshooting==

@@ Line 4: / Line 4: @@
   |Is used in domain=Wood
   |Has name={{PAGENAME}}
   |Has icon=File:planer_icon.png
   |Has icondesc=Planer icon
@@ Line 11: / Line 17: @@
   |Has description=
   |Has certification=https://georgefox.instructure.com/courses/1245
   |Has ace=Needed;Makerhub@georgefox.edu
 }}

@@ Line 74: / Line 74: @@
 # Make sure the material is free of all foreign objects, loose knots, and splits
 # Before turning on the machine, loosen the table lock nuts on the side of the machine.  slide the material into the machine and slowly adjust the table height by rotating the handwheel until the material barely touches.
-# The key is to take off very little material on the first pass and adjust as needed.
+## The key is to take off very little material on the first pass and adjust as needed.
 # Remove piece and adjust wheel to trim desired amount off of work piece.
 # Never attempt to remove more than 1/16” per pass (one turn). Do not over load the motor. Multiple passes result in less tear-out and are easier on the machine.