281
edits
Changes
Jump to navigation
Jump to search
Line 4:
Line 4: + + + + + + Line 11:
Line 17: − |Has make=Formech+ − |Has model=508DT − |Has serial number=2728 − Line 50:
Line 53: − + + − Manual [[Media:Manual-508DT.pdf]]+ Line 64:
Line 68: − Text here+ − Line 75:
Line 78: − + + + + + Line 89:
Line 96: − + + + + Line 104:
Line 114: − +
→Certification
|Is used in domain=
|Is used in domain=
|Has name={{PAGENAME}}
|Has name={{PAGENAME}}
|Has make=Formech
|Has model=508DT
|Has serial number=2728
|Has life expectancy=
|Has year of manufacture or purchase=
|Has replacement cost=
|Has icon=File:Vacuum Former.png
|Has icon=File:Vacuum Former.png
|Has icondesc=
|Has icondesc=
|Has description=
|Has description=
|Has certification=https://georgefox.instructure.com/courses/1305
|Has certification=https://georgefox.instructure.com/courses/1305
|Has ace=Sara Wytsma;swytsma23@georgefox.edu
|Has ace=Nathan Bodenman;nbodenman18@georgefox.edu
}}
}}
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
* '''Toggle Clamp Screws-'''
* '''Toggle Clamp Screws-'''
*'''Draft Angle-''' The wall angle of a mold. This helps in removing the plastic off the mold.
*'''Draft Angle-''' The wall angle of a mold. This helps in removing the plastic off the mold.
Knowing what the different buttons in the touchscreen operation mean is important in operating the vacuum former. The three primary ones are heat , vacuum , and release . For a full list, refer to the manual.
Knowing what the different buttons in the touchscreen operation mean is important in operating the vacuum former. The three primary ones are heat, vacuum, and release. For a full list, refer to the manual.
[[Media:Manual-508DT.pdf|Vacuum Former User Manual]]
[[Media:Vacuum Forming Guide 200715.pdf|Vacuum Forming Guide]]
==Training==
==Training==
====Demonstration====
====Demonstration====
The demonstration for the vacuum former can use one of the provided demonstration molds or a mold that the trainee brings. The trainee must show that they can set up the vacuum former and mold a part.
====Operation====
====Operation====
[[File:Formech_Controls.JPG|none|thumb|600x600px]]
[[File:Formech_Controls.JPG|none|thumb|600x600px]]
* Mold cannot be concave and must slant outwards slightly or it will not be removable from the plastic.
* Mold cannot be concave and must slant outwards slightly or it will not be removable from the plastic.
* Place plastic into the clamps ensuring it completely covers the white seals.
* Place plastic into the clamps ensuring it completely covers the white seals.
* Turn on the heaters. They should take about 15 minutes to warm up.
* Turn on the heaters and set the temperature. The temperature should be 80-120 degrees Celsius.
* The heaters should take about 15 minutes to warm up.
* After 15 minutes roll the heater over the plastic
* Allow the heater to sit over the plastic for 90 seconds if the plastic is 1.8mm thick or 180 seconds if the plastic is 3.3mm thick.
* DO NOT OVERHEAT PLASTIC! this will cause the plastic to develop webbing after the vacuum which will ruin the mold.
* Lift the table.
* Lift the table.
* Turn on the vacuum.
* Turn on the vacuum.
==Certification==
==Certification==
[https://georgefox.instructure.com/courses/1305 Canvas Quiz]
Complete <strong>The Vault - {{PAGENAME}} Module</strong> at the link below to gain access to the {{PAGENAME}}. The Maker Hub Canvas course pertains to all facilities and equipment contained in the Maker Hub; simply complete the quizzes for the facilities/equipment you wish to use in the Maker Hub. Please email <span style="color:blue">makerhub@georgefox.edu</span> if you have any questions.
[https://georgefox.instructure.com/enroll/R6RF69 Maker Hub Canvas Course]
==Troubleshooting==
==Troubleshooting==
Make sure to put draft on your form to prevent sticking.
Make sure to put draft on your form to prevent sticking.
If the plastic is not hot enough it won't pull down over the form.
If the plastic is not hot enough it won't pull down over the form.
If the plastic is too hot then it will develop webbing during the vacuum
==Maintenance==
==Maintenance==
!Done By
!Done By
|-
|-
|Replace sanding Belt/Pad
|Inspect
|As Needed
|As Needed
|Ace/Tech
|Ace/Tech
|}
|}