Changes

##Remove the focusing tool and return it to its home.

##Remove the focusing tool and return it to its home.

##Press the USB icon found in the bottom right corner of Job Control to connect to the laser cutter. The laser should beep a few times and then a the background of job control will change to a honeycomb pattern to represent the actual honeycomb table. Also, the USB icon will change to a play icon.

##Press the USB icon found in the bottom right corner of Job Control to connect to the laser cutter. The laser should beep a few times and then a the background of job control will change to a honeycomb pattern to represent the actual honeycomb table. Also, the USB icon will change to a play icon.

#'''Cutting with Job Control'''

# Cutting with Tortec Ruby

##After you send your design to Job Control your design will be named with the name of your Inkscape file, which will appear in the “Jobs” window on the right. If you do not see your job (your design), be sure to select [See All] at the bottom of that window. This lets you see files ALL dpi types, rather than just a specific dpi type. You can check the print preview by double clicking the box showing your preview in the bottom right.

##Using the arrow keys on the laser cutter, move the head until the laser pointer is positioned on your material where you want a corner of your cut to begin. You’ll notice (assuming that you’ve connected the laser cutter to Job Control) that the curser moves within Job Control as you move the laser head.

## First, you need to get the image from inkscape into Trotec Ruby. This can be done by simply downloading the file and dropping it into Trotec Ruby.  

##Double click/drag your job onto the honeycomb area and position it relative to the cursor. You’ll notice that the corners of your job will snap to the cursor.

## Second, you will click onto the design tab. All you need to do is verify that everything is the correct color that you need and everything looks fine. Once completed. Click on the blue "Create Job" button. This will allow you to move on.

##Move the laser head/cursor around to make sure your job fits onto the material you are using. Move the cursor to the opposite, diagonal corner from the one you started from and make sure that the laser head is not off an edge of the material.

[[File:Ex1.png|thumb|600x600px|none]]

##Then select your material at the top left. There are two dropdown menus, one for general material groups, and one for specific material profiles. These settings control the laser’s speed and power which are fine tuned for the material you select.   [[File:Mitch5.jpg|thumb|600x600px|none]]

## Third, you will need to prepare your cut/engrave. To do this you will need to align the laser with where you want to cut by dragging the grey square box. Then you need to select the material that you will be using to cut/engrave. DO NOT CHANGE ANY SETTINGS WITHOUT APPROVAL FROM SUPERVISOR.  

##To see the duration of the job, you can click the Update in the bottom left. You are ready to click the Play button in the bottom right. For bigger jobs, the Laser Cutter will take a little bit of time to read the design. If it does not start immediately, don’t be scared. Just be supportive and it will begin shortly. If it does not start at all, ask for help from the supervisor.

[[File:Ex3.png|thumb|600x600px|none]]

##Once the job starts, stay with it. Be sure it is actually engraving/cutting the material. Don’t open the lid (or even lean on it) as this causes the job to cancel without the ability to resume it. If the lasercutter is not doing what it should be click pause in the bottom right of Job Control, or stop it entirely with the stop button. Consult the supervisor for assistance. If something has gone very wrong, lifting the lid will immediately stop the machine, though this is not recommended under normal circumstances.[[File:Mitch6.jpg|thumb|600x600px|none]]

## Finally, to produce the image press the "Push to Laser" button, this will open the next tab

##After the job is completed reset the space by cleaning out any scrap materials from the bed and deleting the job from job control and Inkscape.

[[File:Ex4.png|thumb|600x600px|none]]

## To start the cut/engrave just press the play button. Remember to RESET THE SPACE once your cut/engrave is don't and not to leave any material in the laser cutter.  

#'''Cutting with the Rotary Tool'''

#'''Cutting with the Rotary Tool'''

##The Rotary Tool lets you cut and engrave cylindrical objects, the most popular of these being Hydroflasks. This part applies after you have already sent the file from Inkscape to the Laser Cutter.

##The Rotary Tool lets you cut and engrave cylindrical objects, the most popular of these being Hydroflasks. This part applies after you have already sent the file from Inkscape to the Laser Cutter.